Amana Tool – 47154 Karbidová špička bez pilníku 0,015 Radius x 1/2 Dia x 3/8 x 1/4 Shan 1/2-Inch

Name: Amana Tool – 47154 Karbidová špička bez pilníku 0,015 Radius x 1/2 Dia x 3/8 x 1/4 Shan 1/2-Inch
Brand: Amana Tool
SKU: 0696735424091
Price: 1484.34 CZK
Availability: InStock

Brand:Amana Tool

3.7/5

Kč
1484.34

Máme skladem širokou škálu spojovacích prvků ideálních pro mnoho aplikací v domácnosti, na farmě, v podnikání, v automobilovém průmyslu a v průmyslu. Většina našich spojovacích prvků má lehké zinkování na oceli, což poskytuje povrch odolnější proti korozi. Prodáváme také potažené a nerezové výrobky pro dodatečnou odolnost proti korozi. Máme skladem mnoho druhů spojovacích prvků od nízkouhlíkové oceli až po kalenou, tepelně zpracovanou ocel. Ne všechny spojovací prvky jsou použitelné pro všechny aplikace, takže se ujistěte, že je důkladně otestujete a získejte názor licencovaného stavebního nebo certifikovaného stavebního nebo stavebního inženýra, než se na tyto spojovací prvky spolehnete v situacích, kdy by selhání mělo za následek poškození majetku nebo osob.

Množství

Přidat do košíku Kup nyní

EAN: 0696735424091

Kategorie Elektrické a ruční nářadí, Díly a příslušenství elektrického nářadí, Díly a příslušenství k frézám, Router Bits, Přímé, Spirálové a obrubovací bity, Kartáče na obruby,

Celková délka (L) 1-7/8. Stopka (D) 1/4. Výška sečení (B) 3/8. Rádius (R) 0,015 (0,4 mm). Průměr (D) 1/2.

Brand	Amana Tool
Country of Origin	China
Domestic Shipping	Item can be shipped within U.S.
International Shipping	This item can be shipped to select countries outside of the U.S.
Item Dimensions LxWxH	0.75 x 0.75 x 2 inches
Item model number	47154
Manufacturer	Amana Tool
Material	Carbide
Product Dimensions	0.75 x 0.75 x 2 inches; 0.64 Ounces
Shank Type	Straight
Tool Flute Type	Straight

5 Star

4 Star

3 Star

2 Star

1 Star

Napište svou recenzi

Váš email nebude zveřejněn. Všechna povinná pole jsou označena^*

Vase hodnoceni

Scritto da: K Medlar

Great bit for trimming laminate!

This bit worked great on my laminate counter tops and backsplashes. I first flush trimmed them and then use this bit for finishing. This got rid of a lot of the glue and I didn't have to file the edges much or not at all. It does take some setup time, but nothing like a bit such as a drawer lock bit, which are way more tricky. I also used an extended base on my trim router (prevents dipping) and that makes a big difference. Quick and very smooth. You can make an extended base which isn't too hard or get one from Woodhaven who makes them for many trim routers.

Scritto da: E. Hays

Speeds up the process

I had this bit a couple of years ago but wore it out. I wasn't sure who made it so just now got around to getting another. I just delivered another laminated cabinet job and used this bit for my finish edges. It cuts well and the built in roundover saves my helper a lot of file work. I have at least 15 palm routers (all top brands) and don't believe any of them are perfectly square with the bases so there's still a little touch up but not nearly as much as with just a flush trim bit. The bit isn't made for hogging the first cut (wish it was) but does an excellent job on the last pass. I recommend it although I've only used this bit for one job of about 30' of convience store cabinets and check out counter so I can't say how many feet it'll trim. If you're seriously into production work, order several and always have a sharp one handy (they're cheap enough). If you're just a weekender it'll probably last you forever.

Scritto da: J. Smith

I think it would work much better if it only had the radius portion

I see nothing wrong with the quality of this bit, but I totally agree with other reviewers about the difficulty in getting it adjusted right. If you were to adjust this as shown in the instruction sheet that comes with it, you will remove the colored top layer of your edge band laminate. The lower cutting edge, below the radius portion is tapered. I think it would work much better if it only had the radius portion, and no cutting edge between the radius and the bearing. But I was able to use it after careful height adjustment and testing on scrap.

Scritto da: STEVEAREINO

No file bit means no filing great product

This is a must-have router bit for doing laminate don't hesitate works very well minimal filing needed after use

Scritto da: ANTHONY C. TATRO

great product

I really like the idea of not having to file the sharp edges of the laminate, it does take a delicate touch to adjust and use or you will damage the laminate

Scritto da: Jeff

Nice tool bit

This is a very nice tool bit. It is hard to set up but once set you need to keep it in your power tool. It would be nice if I had two routers when I used this bit. Otherwise the bit is excellent.

Scritto da: Amazon Customer

Five Stars

As advertise

Scritto da: Amazon Customer

Five Stars

Great item. Fast shipping