E-Z Lok SK31020 Sada šroubových vložek se závitem, 304 nerezová ocel, velikost závitu 3/8-24, instalovaná délka 0,750 (balení 10 ks)

Brand:E-Z LOK

2.5/5

1852.22

E-Z Lok vyrábí závitové vložky pro kov, plast a dřevo. Společnost má sídlo v Gardena, CA.

SADA OBSAHUJE – Praktická sada obsahuje závitové vložky cívky pro kov, vrták, závitník STI, nástroj pro instalaci závitové vložky a nástroje pro ulomení třmenu. PRO POUŽITÍ S APLIKACÍ – Kovové závitové vložky jsou navrženy pro použití s ​​měkkými kovy: hliník, litina, hořčík atd. DRÁT Z NEREZOVÉ OCELI – Sada obsahuje závitové vložky z nerezové oceli, které jsou odolné vůči korozi a odolávají teplotám až 800 °F. RYCHLE OPRAVTE POŠKOZENÉ ZÁVITY – Rychle opravte poškozené závity nebo vyztužte závitové otvory v měkkých kovech pomocí této sady na opravu šroubovicového závitu.
Brand E-Z LOK
Country of Origin United Kingdom
Fastener Type E
Item model number SK31020
Manufacturer E-Z LOK
Material Stainless Steel
Package Dimensions 8.39 x 4.69 x 1.26 inches; 8.8 Ounces
Size 3/8"-24 Thread Size, 0.750" Installed Length
Thread Size 3/8"-24

2.5

3 Review
5 Star
60
4 Star
0
3 Star
0
2 Star
0
1 Star
40

Napište svou recenzi

Váš email nebude zveřejněn. Všechna povinná pole jsou označena*

Scritto da: Madelyn Chapman
Excellent Product
Worked perfectly - Saved me $1000, since I didn't have to replace the casting The thread that stripped out had a .5 counter-bore 3/8deep. Then the thread went another 1.25 inches. This was perfect, the tap didn't score the bore at all, and I was able to torque the bolt to the required specification. I will definitely use them again when I strip out another thread. Thanks, Sam
Scritto da: Joy Porter
Wrong size tap!
I ASSUMED that everything in the pack was correct, as it listed the tap as 3/8” x 24. I drilled the hole with the 25/64” bit provided and then tapped it with the tap. I then installed the thread coil. However, when I tried to thread the 3/8x24 bolt, it wouldn’t start. I then discovered the reason was the tap was 3/8x16! I couldn’t back the coil back out! My only solution was to try to retap the coil with my own 3/8x24 tap. This required several hours of time and literally destroyed my tap!!!!
Scritto da: Laurie M. Kiser
Best quality thread repair kit
I have done this process 2 or 3 times before with good results. The hardest part of the job is making the hole and tap straight. This kit has the highest quality tools and the new threads are 100 x stronger than original aluminum alloy. Drill bit is extremely sharp. The bit and tap seemed to self level making diy hand tools ok. Both of the repairs I did were perfectly straight in spite of me. The coil did need A LOT OF lubricant to install correctly. I had to use liquid assembly lube to get the coil to seat properly. Spray lube wasn't enough. Not the cheapest kit but totally worth the extra few dollars.

Související produkty

Objevte naši mezinárodní síť

Dodáváme do 28 zemí, více než 200 000 produktů. Zůstaňte v obraze, přihlaste se k odběru newsletteru.

Array