Regulace objemu vzduchu řady Penn F93 pro hluboké studny, otevírá se při poklesu tlaku, bez kohoutku, bez přetlakového ventilu F93A-1C

Brand:Johnson Controls

3.7/5

3069.73

Regulátory množství vzduchu pro hluboké studny řady F93 řídí množství vzduchu v obytných nádržích na vodu v systémech s hlubokými studnami. Hluboké vrty jsou více než 25 stop (7,6 m) hluboké. Ovládací prvky řady F93 automaticky udržují objem vzduchu v zásobních nádržích systémů s hlubokou vodou tím, že umožňují unikání vzduchu z nádrže a do okolní místnosti, když hladina vody v nádrži klesne (zvýšení objemu vzduchu). Hluboké ovládání F93 otevírá vzduchový ventil při poklesu hladiny vody v nádrži vypouští přebytečný vzduch z nádrže při tlacích až 100 psig (690 kPa). F93H má vypouštěcí ventil minimálního tlaku, který zabraňuje snížení tlaku v nádrži pod 25 psig (172 kPa). Tento model používejte v aplikacích, kde může rychle odtékat voda. Důležité informace o aplikaci produktu naleznete v části F93 Series Controls Air Volume Controls pro produktový bulletin Deep Wells (díl č. 24-7664-3000).

robustní tělo z norylu (vysoce výkonný termoplast) odolává mechanickému poškození a korozi.
Country of Origin USA
Item model number F93A-1C
Manufacturer Johnson Controls, Inc
Package Dimensions 10.2 x 3.94 x 1.73 inches; 7.05 Ounces

3.7

8 Review
5 Star
79
4 Star
12
3 Star
4
2 Star
2
1 Star
3

Napište svou recenzi

Váš email nebude zveřejněn. Všechna povinná pole jsou označena*

Scritto da: JS
Water tank switch
Fit great no issues
Scritto da: Beaty Wade Tharp
Fine valve
This style of valve is just fine for its function. My only wish is some ingenious engineer would figure out a way for the air vent portion of the valve to not get plugged up. I.e. some sort of wiper assembly that cleans off the air vent port as the float cycles up/down.
Scritto da: JERED ECKLE
Works like a champ!
Replaced one just like it in style. Immediately started working like it should after a few drain & fills of the tank!
Scritto da: MnBoy
It works.
Turned power off to deep well. Drained the water from the existing metal water tank through faucets. Waited until all the water... then air... left the tank. Closed the faucets. Took the old volume control out and put the new one in. This was a fairly easy procedure. Turned power on and waited for tank to fill. I could hear the air escaping the valve, which I did not hear on the old valve. The tank filled properly and I turned the faucets on to bleed air from lines. Pump runs only a fraction of what it did prior to new valve installation. I think the price is a bit high, but if it helps the pump by running less it is probably worth it.
Scritto da: Patrick
Identical to original.
Works fine but the arms on these floats are not a solid rod and that is what went bad on my old one. The arm bend up . These look identical to my original so i decided to beef up the rod with a piece of 8 awg solid copper wire soldered to the float arm. If not for the weak float arm this device would probably never fail.
Scritto da: Quail Valley Farm
Can't go wrong with Johnson Controls components
This switch closes the air pressure relief valve when the water level in the tank reaches the appropriate level. The switch was failing and dripping water in the pump house, non-stop. This is the exact same brand/model I replaced, and the one that failed was on the tank when I purchased the property in 2003, demonstrating its longevity. Given this is a farm tank, serving a home with a pool, and the property, it gets a significant workout. I suspect that because the well is inside of a structure, this switch and other components last somewhat longer than they would if the well system was exposed to the elements.
Scritto da: Mark Williamson
Says Penn, not Johnson controls.
Using it as a spare, not installed yet.
Scritto da: Roark
Works very well and has “secret” ability. :)
Perfect replacement for my deep-well system. Something not mentioned in the description is this has an *optional* outlet for gauge/pressure switch that is pre-threaded. If you dont need this feature, simply do nothing. This threaded recess does NOT by default connect to the tank-side pressure. If you want this feature, simply drill a small (tiny is fine!) hole in the threaded recess and screw your gauge or pressure switch in. That little hole connects the gauge to the pressure side of things. This means one unit can fill the role of two. Simply drill the hole to allow connection of a pressure switch or gauge. Neat!

Související produkty

hot
York S1-03100880001 Náhradní díl
0.1/5

Kč 8468.12

York S1-03100880001 Náhradní díl
0.1/5

Kč 8468.12

Objevte naši mezinárodní síť

Dodáváme do 28 zemí, více než 200 000 produktů. Zůstaňte v obraze, přihlaste se k odběru newsletteru.

Array