0
0

Celkový:Kč 0.00

Viz košíkPřekontrolovat
LoginRegister
0

Celkový:Kč 0.00

Viz košíkPřekontrolovat
LoginRegister

J-B Weld 8277 WaterWeld epoxidová tmelovací tyčinka – 2 oz., šedobílá 1 balení tmelové tyčinky

Brand:J-B Weld

3.3/5

Kč
619.85

Vodní svar ucpe nebo utěsní netěsnosti a zalepí díry a praskliny téměř v čemkoli. Ideální pro opravy potrubí, palivových nádrží, vany a sprchy, odtoků, bazénů a lázní, lodí a nádrží na pitnou vodu; nastavení probíhá i pod vodou. Po vytvrzení jej lze vrtat, závitovat, pilovat, brousit a lakovat. Vodní svar má dobu tuhnutí 15-25 minut a ztvrdne za jednu hodinu. Vodní svar vytvrzuje do téměř bílé barvy, má pevnost v tahu 900 psi a vydrží teploty až 300 F.

Množství
Přidat do košíkuKup nyní

EAN: 043425082770

Kategorie Automobilový průmysl, Údržba automobilů, Těsnicí prostředky,

UDĚLEJTE SAMI: Velký nebo malý, můžete si ho vyrobit pomocí J-B Weld. Naše vysoce odolné epoxidy a lepidla opravují a obnovují hned napoprvé. J-B Weld poskytuje vynikající výkon, kvalitu a výsledky pro nejsilnější bond na světě. POVRCHOVÉ APLIKACE: Železo a nerezová ocel, měď a mosaz, hliník a bronz, sklolaminát a plasty a PVC. VLASTNOSTI A SÍLA PRODUKTU: J-B Weld WaterWeld má pevnost ve smyku 1300 PSI, vydrží trvalé teploty až 300F (149C) a občasné teploty 350F (176 stupňů Celsia) a je plně chemicky odolný vůči ropě, hydraulickým kapalinám a dalším chemikáliím. vyléčený. ČAS VYTVRZENÍ A TUHNUTÍ: Po ručním hnětení dvousložkového složení trvá WaterWeld 25 minut, než se tuhne a vytvrzuje za 1 hodinu. J-B Weld WaterWeld set a barva vytvrzení je šedobílá. J-B WELD WATERWELD: Ručně mísitelná dvousložková epoxidová tmelící tyčinka, která dokáže vytvrdnout pod vodou a je ideální pro opravy vodovodních potrubí, palivových nádrží, van a sprch, odtoků, bazénů a lázní, lodí a nádrží na pitnou vodu a další! J-B Weld WaterWeld je certifikován NSF a je bezpečný pro kontakt s pitnou vodou.
Brand J-B Weld
Brand ‎J-B Weld
Color Off White
Color ‎Off White
Compatible Material Porcelain, Fiberglass, Brick, Ceramic, Plastic, Carbon Fiber, Concrete, Metal, Rubber, Marble
Compatible Material ‎Porcelain, Fiberglass, Brick, Ceramic, Plastic, Carbon Fiber, Concrete, Metal, Rubber, Marble
Country of Origin ‎USA
Customer Reviews 4.3 4.3 out of 5 stars 9,851 ratings 4.3 out of 5 stars
Domestic Shipping Item can be shipped within U.S.
Exterior ‎Painted
Full Cure Time ‎60 Minutes
International Shipping This item can be shipped to select countries outside of the U.S. Learn More
Is Discontinued By Manufacturer ‎No
Item Form Stick, Putty
Item Form ‎Stick, Putty
Item model number ‎8277
Item Package Quantity ‎1
Item Volume ‎59.14 Milliliters
Item Weight ‎2.46 ounces
Lift Type ‎....
Manufacturer ‎JBWeld
Manufacturer Part Number ‎8277
Material WaterWeld Epoxy Putty Stick
Material ‎WaterWeld Epoxy Putty Stick
Model ‎8277
Package Information ‎Tube
Product Dimensions ‎1 x 4 x 7 inches
Tensile Strength ‎1300 PSI
Water Resistance Level ‎Waterproof

3.3

12 Review
5 Star
66
4 Star
14
3 Star
9
2 Star
4
1 Star
7

Napište svou recenzi

Váš email nebude zveřejněn. Všechna povinná pole jsou označena*

Scritto da: Deisai
Works great for my sprinkler pipe
It works great on a L shape elbow pvc joint in my sprinkler box (about 80psi). There is a very small leak in my sprinkler box, found last fall and confirmed this spring when turn back on the water (photo 2), there a few hair size water shoots out from it. I removed the component and brings to Home Depot, but they said the manufacture is no longer making it (or out of business), and they do not have any replacement in similar size. So for me, try some alternative solution is the only way to do before spend hundreds to hire professional. I decide to give this a try to this patty before really hire someone to do it, and thanks to many other reviews in this post, even a lot of people says it doesn't work with pressured pipe, I did see there are people successfully make it works. Based on all other people's experience, I did the following steps with extra caution: 1. clean up all the dirt and debris, wipe out clean with paper towel. 2. rough the surface a little bit with a wood sandpaper (barely add some scratch on the surface, to improve the bond between this patty and the pipe). 3. discards the first1 inch of patty on the edge (some people recommend so), then take a about 1 inch of patty for first application. knead it to bar/snake shape and fold it, repeat for dozens of times. 4. after it fully mixed and soft like peanut butter, make it like bar/snake, wrap it around the leaked position (like a ring over your finger), push it to the surface and smooth the edge (like a band aid around the ring over your finger). 5. wait 1 hour to 2 hour for first application to harden a bit (the first application only becomes slightly harden after an hour), then do the 2nd application same way to "patch" the 1st application (use 1st application to seal the leak, 2nd application to seal any potential leak of 1st application). 6. wait 3 days instead of just 1 day to let it fully cured (assume there are moisture in the pipe and it take longer to dry) So far it works well after turning water back on and no more leanings. I will keep monitoring my pipe, in case if it leaked again, I will update here. note1: the product i received says its strength is 4370 psi (picture 1), which is much higher than the label in old picture and another product in home depot. I guess that extra strength may also helps if the product is fully cured. note 2: if your hole is larger, you may need more putty to add extra strength than how much i uses. but i still recommend multiple applications than use everything in one shot.
Scritto da: Sandra Souder
Worked where nothing else would
This stuff works great! The inside corner of the pvc pipe “T” had a crack in it, in a very inconvenient location. To change the fitting would’ve been an extensively long and tedious repair. I futilely tried other methods first. So I got JBWeld Water Weld. I prepared the surface as the instructions said. However, I did shut the water main off and released all the water pressure by turning all the faucets on in the house, so any water in the lines would drain out. Then I washed off the dirt and sanded the surface, cleaned it with alcohol and then followed the application instructions. Knead the epoxy (with kitchen gloves, they work best) til it’s a uniform color throughout, then I applied it to the prepared surface. I used 2 packs of the JBWeld Water Weld so that it would wrap all the way around the “T” forming like a cast around it. The cure time they say is 1 hour, however, I waited 4 hours because I used two packs and because I wanted to be sure it had plenty of time to cure before I turned the water back on. It actually worked! I was so happy! I HIGHLY recommend this product to anyone who has a PVC crack in a very complicated spot! Be sure to push a little of the epoxy into crack if you can. Don’t stuff it full, but just a little and then cake it around like a cast. Give it time to cure. It’ll work!
Scritto da: The Wild Rover (Rob E)
Once fully cured, it works as advertised.
Not much to comment about this product. It works as expected. There's one important note about the listed cure time, it took way longer for me. Consider giving at least 48 hours for full cure before attempting to use the repaired item. I used this for an emergency faucet repair and was thoroughly disappointed. I gave it about 12-14 hours before trying to use the item and a hole blew out of the repair almost immediately. I put more over top and allowed more than 24 hours to cure. It still leaked, but at a much lesser level. I did notice that after 48-72 hours, it seemed to have fully cured and the leak had lessened even further. If you use this, give it at least 48-72 hours to fully cure before first use.
Scritto da: Amazon Customer
Very good at stopping leaks!
Liked how it was easy to mix and measure amount of epoxy puddy. Limited working time cures Fast, if you fiddle with it too long it will begin to set up on you, you get 30 min until it's too stiff to work anymore. Strong epoxy puddy-can handle purity much anything residential and may even be applicable for some commercial plumbing applications. Good product at a reasonable price, though cheeper is always welcome.
Scritto da: Tom
This is the stuff
Needed to re-repair a white porcelain sink with a bad chip. The previous repair just didn't cut it and rust would soon make a hole. This stuff was easy to apply and I expect it to last longer than I will. It's JB Weld for gosh sakes. As for color match, don't be concerned with the off color. Once it cures, it's a perfect match. I didn't even need to sand it. Just formed it in with my thumb. Done.
Scritto da: Florida Customer
J-B WELD WE TRUST
Relative's house developed crack during Hurricane Ian. Feet of standing water in what was a non-flood zoned area proved to be too much for cinderblock house w/stucco covering. Insurance company would not cover repair and inside water. FEMA fellow was nice to point out water's entrance point. SOOOO, we are giving this a shot. We have used this on our formerly leaking swimming pool's cracks with GREAT results. Time will tell if this will do the trick. We bought many packs of it. It is VERY easy to use. Wish us luck.
Scritto da: E.Mathias
Very easy to handle and use
This stuff worked as intended. I put on some rubber/latex kitchen gloves. Ripped off a piece and played with it until it was a solid color. Pressed it up against the leaky part of the pipe under the kitchen sink and worked like a champ.
Scritto da: Amazon Customer
Does it ever work
My pool pipe was leaking and this is the trick. Easy apply and it gets hard...It works very well
Scritto da: pendram manojkumar
कोई भी ना ले
घटिया सामग्री है मैं तो फंसा कोई भी मत फँसना pvc पाइप पे काम नहीं किया 900 रुपए गए पानी मे
Scritto da: Amazon Customer
brand name
great stuff
Scritto da: Sudhakar Nayakude
Not useful for pvc water tank leak repair
I was used this product on pvc water tank leak repair. But after applying this pest leakage not repaired. Not useful for the product. I don't like.
Scritto da: Gérald Lemire
très bien
très bien

Související produkty

hot
Vibra-TITE - 12535 125 odnímatelný gel se střední silou anaerobní zajišťovač nití, 35 ml pumpička, modrá
3.8/5

Kč 1012.25

Vibra-TITE - 12535 125 odnímatelný gel se střední silou anaerobní zajišťovač nití, 35 ml pumpička, modrá
3.8/5

Kč 1012.25

hot
J-B Weld 31914 Red High Temperature RTV silikonové těsnění a těsnící hmota - 10,3 oz. Červená 10,3 oz
3.6/5

Kč 1024.87

J-B Weld 31914 Red High Temperature RTV silikonové těsnění a těsnící hmota - 10,3 oz. Červená 10,3 oz
3.6/5

Kč 1024.87

hot
GEAR AID Seam Grip SIL silikonový tmel pro silnylonové stany a plachty 1,5 oz
3.6/5

Kč 712.46

GEAR AID Seam Grip SIL silikonový tmel pro silnylonové stany a plachty 1,5 oz
3.6/5

Kč 712.46

hot
J-B Weld 8277 WaterWeld epoxidová tmelovací tyčinka – 2 oz., šedobílá 1 balení tmelové tyčinky
3.3/5

Kč 619.85

J-B Weld 8277 WaterWeld epoxidová tmelovací tyčinka – 2 oz., šedobílá 1 balení tmelové tyčinky
3.3/5

Kč 619.85

Objevte naši mezinárodní síť

Dodáváme do 28 zemí, více než 200 000 produktů. Zůstaňte v obraze, přihlaste se k odběru newsletteru.

Array

Celkový:Kč 0.00

Viz košíkPřekontrolovat

Kategorie

Všechny kategorie
Jídelní lístek Kategorie U Vozík

Menu